Old Tub Removal
We disconnect the old tub or shower pan, haul it out, and dispose of it. We also check the subfloor and wall framing for rot or water damage while everything is open, because that is the only time you can see it.
Licensed local installers for safe, step-free bathing
Walk-In Tub Installation Scottsdale AZ Done Right the First Time
Walk-In Tub Installation Scottsdale AZ is what we do: we set the tub, run the PEX and copper lines, wire the pump, and waterproof every seam so your bathroom stays dry. Whether you need a walk-in bathtub installation Scottsdale homeowners can step over safely, or a full accessibility upgrade for aging parents, we handle the whole job. Most installs finish in one to two days, and we pull the permits so the work passes inspection.
Careful work. Honest options.
About this service
Walk-In Tub Installation Scottsdale AZ: What the Job Actually Involves
Walk-In Tub Installation Scottsdale AZ means removing the old tub or shower pan, checking the subfloor for water damage, and setting a new low-threshold tub with a door that seals tight. We frame the opening, run a dedicated GFCI circuit for the pump and heater, connect the shower valve and drain, then seal everything with a waterproofing membrane and silicone caulk. Hydrotherapy jets, grab bars, and a handheld shower wand get tested before we call it done.
Scottsdale homes run into two big issues: hard water that eats through old caulk lines and fixtures, and slab-on-grade bathrooms where moving a drain means cutting concrete. We scope that on the first visit so there are no surprises. If you have been searching walk-in bathtub installation near me Scottsdale and getting vague quotes, we give you a real number after we see the drain location and the electrical panel.
- ✓ Step Over a 4-Inch Threshold
- ✓ Hydrotherapy That Helps Joints
- ✓ Built-In Seating and Grab Bars
- ✓ Fewer Falls, Fewer ER Visits
What's included
What Our Walk-In Tub Installation Includes
Every job we quote includes the labor, the permit, and the waterproofing that makes the install last. The tub itself and any upgrades are priced separately so you can see exactly what you are paying for.
Drain and Supply Tie-In
We connect the new tub drain and overflow, then tie the supply lines into your existing PEX or copper. If the drain has to move, we cut the slab, reroute, and re-pour. All connections get pressure-tested before the wall closes.
Dedicated GFCI Circuit
Walk-in tub pumps and heaters cannot share a circuit with your lights. We run a dedicated line from the panel, install a GFCI outlet, and test it under load. This is the part most cheap installs skip, and it is the part that keeps you safe.
Waterproofing and Tile
We hang cement backer board, roll a waterproofing membrane over the wet walls, and set new tile around the tub. Epoxy grout and silicone caulk finish the seams. This is what stops hard water from eating into the wall cavity.
Grab Bars and Seating
We anchor grab bars into solid blocking, not drywall, and set them at the height that works for your household. The tub's built-in seat gets checked for level and stability before we call the job done.
Full Test and Walkthrough
We fill the tub, run every jet, cycle the door a dozen times, and check for drips at the drain and valve. Then we show you how to clean the door gasket and where the shutoff valves are. You use the bathroom the same night.
How it works
Our Walk-In Tub Installation Process
We measure the alcove, check the drain location, and inspect the subfloor and wall framing for rot or old water damage. We also verify your electrical panel has room for a dedicated GFCI circuit. This visit takes about 45 minutes and you get a written price the same day.
You pick the tub model, jet package, and finish. We order through Kohler, American Standard, or Delta depending on what fits your space and budget. Most tubs arrive in 5 to 10 business days, and we schedule the install the week it lands.
Day one we pull the old tub or shower pan, cut back damaged drywall, and check the studs. If the drain needs to move, we cut the slab, reroute the PEX, and re-pour. We hang cement backer board and roll a waterproofing membrane over every wet wall.
We set the tub level on a mortar bed, connect the shower valve and drain, and tie the pump and heater into their own GFCI circuit. A pipe wrench, plumber's snake, and moisture meter all get used here to confirm no leaks and no hidden damp spots behind the walls.
We fill the tub, run every jet, open and close the door a dozen times, and check for drips at the drain and valve. Then we walk you through the controls, the warranty, and how to keep the door gasket clean. The whole job usually wraps in one to two days.
STEP 01On-Site Measure
We measure the alcove, check the drain location, and inspect the subfloor and wall framing for rot or old water damage. We also verify your electrical panel has room for a dedicated GFCI circuit. This visit takes about 45 minutes and you get a written price the same day.
Tools & methods
Tools and Methods We Use
Wet Saw and Tile Saw
Used to cut porcelain and natural stone tile around the tub surround. A wet saw keeps the cut edges clean and reduces dust, which matters in an occupied home.
Notched Trowel and Grout Float
The notched trowel controls thinset thickness so tile sits flat. The grout float packs epoxy grout into the joints without leaving voids that trap water.
Pipe Wrench and Plumber's Snake
The pipe wrench handles drain and supply connections. The snake clears any blockage in the existing drain line before we tie the new tub in, so you do not inherit a slow drain.
Moisture Meter
We scan the subfloor and wall framing for hidden damp spots before closing anything up. Finding moisture early is how we avoid mold problems six months down the road.
Laser Level and Stud Finder
The laser level keeps the tub and tile lines true. The stud finder locates solid blocking for grab bars so they hold real weight instead of pulling out of drywall.
Caulking Gun and Oscillating Multi-Tool
The caulking gun lays a clean silicone bead at every seam. The multi-tool cuts back old caulk and drywall without damaging the surrounding surfaces.
Real results
Before and after.
Walk-In Tub Installation
Old Town Tub Swap with Drain Repair
A 1962 ranch home in 85251 had a cast iron tub with a rusted drain and soft subfloor from a slow leak. The homeowner could not step over the 17-inch wall safely anymore.
After: We cut out the rotted subfloor, replaced a 4-foot section, rerouted the drain in PEX, and set a low-threshold walk-in tub with grab bars. The job took three days and the floor is now solid.
Book this service →
Walk-In Tub Installation
North Scottsdale Hydrotherapy Upgrade
A 2005 home in 85255 had a standard soaker tub the owners never used. One of them had arthritis and wanted jets but assumed it meant a full remodel.
After: We swapped the tub for a walk-in model with 10 hydrotherapy jets and an inline heater, reused the existing drain, and refreshed the tile surround. Two days on site, no slab cutting.
Book this service →
Walk-In Tub Installation
Fountain Hills Accessibility Package
A homeowner in Fountain Hills was recovering from hip surgery and could not use the guest bathroom safely. The tub had no grab bars and the exhaust fan had failed years earlier.
After: We installed a walk-in tub with a built-in seat, added three grab bars, replaced the exhaust fan, and set a comfort-height toilet. The job finished in two days and passed inspection.
Book this service → Problems we solve
Problems a Walk-In Tub Installation Scottsdale AZ Solves
Most of our customers call because something in the bathroom is already failing. Here are the issues we run into most often and what we do about them.
Ask a pro →Old tub with a 17-inch step-over wall
We replace the tub with a low-threshold walk-in model and add grab bars anchored into blocking. The step-over drops to about 4 inches, and the door swings open so you walk in instead of climbing over.
Hard water stains and failing caulk lines
We strip the old caulk, treat the surface, and finish with epoxy grout and silicone caulk rated for wet areas. We also check the shower valve and supply lines while the wall is open so we are not back in six months.
Mold and mildew behind the tub surround
We remove the damaged drywall, treat the framing, and rebuild with cement backer board and a waterproofing membrane. We also size and install an exhaust fan that actually clears the room, vented through the roof.
No dedicated circuit for a tub pump
We run a dedicated GFCI circuit from the panel to the tub location, install the outlet, and test it under load. All work follows NEC code and gets inspected when the job requires a permit.
Proof you can check
Licensed, Insured, and Reviewed
- Arizona ROC Contractor License · Arizona Registrar of Contractors
- EPA Lead-Safe Certified Firm · U.S. Environmental Protection Agency
- Waterproofing Membrane Certification · Manufacturer-trained applicator program
- OSHA Safety Compliance · Occupational Safety and Health Administration
Most Scottsdale installs run $3,200 to $9,500 in 2026, including the tub, labor, and permit. A basic soaker with a door sits near the low end. Add hydrotherapy jets, an inline heater, or a drain relocation and you climb toward the top. If we have to cut slab to move the drain, budget another $800 to $1,800.
A straight swap takes one to two days on site. Ordering the tub adds 5 to 10 business days before we start. If we are moving the drain or repairing water damage under the floor, plan on three to four days. We give you the exact schedule in writing after the on-site measure.
Yes, if you plan to age in place or you already have mobility issues. The lower threshold and built-in seat cut fall risk, and hydrotherapy jets help with arthritis and circulation. If you are flipping a house or you never use a tub, a tub-to-shower conversion usually returns more at resale.
Original Medicare does not cover walk-in tubs because they are considered home modifications, not durable medical equipment. Some Medicare Advantage plans and VA benefits do help. We can provide an itemized invoice with the medical necessity language your plan may ask for. Check with your plan before you buy.
Ready when you are
Get Your Walk-In Tub Installation Scottsdale AZ Quote
Call us and we will measure your bathroom, check the drain and panel, and hand you a written price the same day. Licensed, insured, and permit-pulled on every job. If you want a walk-in tub installed correctly the first time, this is the call to make.
Get Free Quote +18556124434 →
Request an appointment
Contact Our Scottsdale Bathroom Team
Call +1 855-612-4434 or email [email protected] and we will get back to you the same business day. We answer the phone Monday through Friday, 8:00 to 18:00, and we schedule walkthroughs across Scottsdale and Maricopa County within a few days. Bring your wish list and your budget.