When you need Sink Installation Scottsdale AZ homeowners can count on, our licensed crew handles everything from a simple bathroom sink replacement Scottsdale swap to a full undermount upgrade. We cut the old fixture out, check the shutoff valves and P-trap, seal the new basin, and pressure-test every connection before we pack up. Same-day appointments are available across Maricopa County.
Sink Installation Scottsdale AZ is the licensed removal and replacement of a bathroom lavatory basin, its drain assembly, supply lines, and the caulk or sealant that keeps water out of your vanity cabinet. It covers cutting or adjusting the countertop opening, setting the new sink level, connecting hot and cold supplies, and testing for leaks under pressure. A basic swap runs two to four hours; a countertop cut for a new undermount basin can stretch to a full day.
Most calls we get in Scottsdale start with a cracked basin, a rusted-out drain flange, or a homeowner who bought a new vanity and needs the sink set before the countertop goes on. Hard water here leaves heavy mineral scale that eats through cheap pop-up assemblies in a few seasons. If you are searching for bathroom sink replacement near me Scottsdale, we can usually walk the job, quote it, and schedule the work the same week.
Every sink job we do covers the full removal and replacement, not just dropping a basin in the hole. Here is what is included in a standard Scottsdale bathroom sink installation, and what we can add if your setup needs more.
We disconnect the faucet, drain, and supply lines, cut through the old caulk, and lift the basin out without damaging the countertop. The old sink leaves with us, so you are not stuck with a porcelain bowl in the garage.
We dry-fit the new sink, confirm the cutout, and set it with silicone caulk or mounting clips as the style requires. The rim or undermount edge gets a continuous seal so water cannot get under the basin.
New braided stainless supply lines, a fresh pop-up drain assembly, and a properly aligned tailpiece into the P-trap. We check the shutoff valves and replace any that will not hold.
We fill the basin, let it stand, then drain it while watching every joint with a dry paper towel. If anything weeps, we fix it before we pack up. You get a sink that is tested, not just installed.
If you are upgrading the faucet at the same time, we install Moen, Delta, Kohler, or Grohe models and connect them to the new sink. It saves a second service call and keeps the finish matched.
We ask for photos of the sink, the cabinet underneath, and the shutoff valves. That tells us whether you have a drop-in, undermount, or vessel sink and whether the countertop needs cutting. Most quotes go out the same day, and you get a firm price before anyone picks up a tool.
Our installer kills the supply at the angle stops, drains the lines, and disconnects the faucet and drain. We cut through old silicone caulk with an oscillating multi-tool instead of prying, which protects the countertop edge. The old basin comes out clean, and we inspect the cabinet floor for water damage while it is open.
We dry-fit the new sink, check the cutout with a laser level, and confirm the drain lines up with the P-trap. For an undermount, we set it with silicone caulk and support clips rated for the basin weight. Drop-in sinks get a fresh bead of sealant under the rim so water cannot sneak past.
New supply lines go in, usually braided stainless, and we connect the faucet, pop-up drain, and tailpiece. We check the shutoff valves and replace any that are seized or weeping. Every threaded joint gets pipe dope or Teflon tape, then we open the valves slowly and watch for drips.
We fill the basin, let it sit, then pull the stopper and watch the drain run. A dry paper towel under the trap tells us if anything weeps. Once it passes, we wipe the countertop, haul the old sink away, and walk you through what we did. Most jobs finish in two to four hours.
We ask for photos of the sink, the cabinet underneath, and the shutoff valves. That tells us whether you have a drop-in, undermount, or vessel sink and whether the countertop needs cutting. Most quotes go out the same day, and you get a firm price before anyone picks up a tool.
Cuts through old silicone caulk and sealant at the sink rim without prying on the countertop. It protects quartz and granite edges from chips during removal.
Loosens and tightens drain nuts and supply connections in tight cabinet spaces. A basin wrench reaches the faucet mounting nuts behind the sink where hands cannot fit.
Lays a clean, continuous bead under the sink rim or around the undermount edge. Silicone stays flexible and resists the mold and mildew that plague bathroom seams.
Confirms the new basin sits level in the cutout. A sink that is off-level will not drain completely and will pool water at the low corner.
Checks the vanity cabinet floor and surrounding drywall for hidden water damage from the old sink. It tells us whether we need to repair the cabinet before setting the new basin.
Cuts quartz, granite, and Cambria countertops when a new sink needs a larger opening. Water cooling keeps the blade from burning the stone edge.
A 1990s drop-in sink in a McCormick Ranch home had a hairline crack that leaked into the vanity cabinet. The cabinet floor was stained and soft near the back corner, and the shutoff valves were frozen open.
After: We removed the old sink, repaired the cabinet floor, and installed a new undermount porcelain basin in the existing quartz countertop. Both shutoff valves were replaced with quarter-turn ball valves, and the new sink passed a full pressure test.
Book this service →
A guest bathroom in 85258 had heavy mineral scale on a builder-grade faucet and a drain flange that had rusted through. Water dripped into the cabinet every time the sink was used, and the drain ran slow.
After: We installed a new Moen faucet and a fresh pop-up drain assembly, cleaned the P-trap, and set a new basin. The drain now empties in seconds, and the cabinet stays dry. The homeowner added a water softener loop later that year.
Book this service →
A powder room in Old Town Scottsdale smelled like sewer every time the sink ran. The trap arm was pitched backward, so water sat in the line and grew bacteria. The sink itself was a small round drop-in with a corroded rim.
After: We re-pitched the drain line, replaced the P-trap, and installed a compact vessel sink with a new faucet. The odor disappeared immediately, and the drain now empties fully with no standing water.
Book this service →Most sink calls start with one of these four issues. Each one gets worse if you wait, and each one is fixable in a single visit.
Ask a pro →We remove the damaged basin, inspect the cabinet for water damage, and set a new sink with a fresh seal. If the cabinet floor is soft, we repair it before the new sink goes in so the repair lasts.
We replace the drain assembly and P-trap, clean the tailpiece threads, and test the joint under full flow. New chrome or brushed nickel trim matches the faucet and stops the drip for good.
We replace angle stops with quarter-turn ball valves during the sink install. They cost little, they turn easily by hand, and they give you a real emergency shutoff at the fixture.
We clean or rebuild the drain path, confirm the vent is working, and test flow after the new sink is set. If the clog is deeper, we run a plumber's snake to clear the branch line.
Most bathroom sink replacements in Scottsdale run $250 to $650 in 2026, including labor, a new drain assembly, supply lines, and haul-away. A simple drop-in swap sits at the low end. Undermount sink installation Scottsdale AZ jobs that require cutting the countertop or adding support clips run higher, and a vessel sink with a new faucet can reach $800 or more.
An undermount porcelain sink paired with a quartz or granite countertop is the best all-around choice for Scottsdale homes. There is no rim to catch water or grow mildew, and the smooth surface handles hard water better than a textured basin. Vessel sinks look sharp in a powder room but splash more. Drop-in sinks are the budget option and the easiest to replace later.
A standard bathroom sink replacement takes two to four hours from shutoff to cleanup. If the countertop needs cutting for a new undermount basin, plan on a full day. Jobs that turn up a failed shutoff valve, a corroded P-trap, or water damage in the vanity cabinet can add an hour or two. We tell you the expected window before we start.
Yes, in most cases you can. If the new sink matches the existing cutout, we set it in the same opening and seal it, no stonework needed. The exception is switching from a drop-in to an undermount, which requires cutting and polishing the countertop edge. We measure your cutout first and tell you honestly whether the new basin will drop in.
Call now and we will walk your sink job over the phone, give you a firm price, and book a same-day or next-day slot. Licensed, insured, and warrantied work from a local crew that knows Arizona plumbing.
Get a Free Quote +18556124434 →Call +1 855-612-4434 or email [email protected] and we will get back to you the same business day. We answer the phone Monday through Friday, 8:00 to 18:00, and we schedule walkthroughs across Scottsdale and Maricopa County within a few days. Bring your wish list and your budget.